Tutorials

Gproxy Tutorial

GProxy tool coded by stefos007 comes with some specific features, one of them is the ability to play sounds. For example, by default, whenever someone in your friend list joins a channel, you get a sound played, or when you receive a whisper you have a different sound. If you want to temporarily(until gproxy.exe is closed) disable all sounds, you can type !sounds in any channel, and you will disable all sounds. If you type !sounds again, you will enable all of them again. If you type !sid in any channel, you will get a list with all sounds available. Also, using the command !sid you are able to disable/enable specific sounds. For instance, after typing !sid, it is possible to find out that the sound related to friend joining game has ID 19. If you want to disable this sound only, you must type: !sid 19 off To enable it back, you must type: !sid 19 on For permanently disabling a sound, you should go to your Warcraft III folder and look for the gproxy.cfg file. Open it with notepad and then change the line with the sound you want to enable/disable, for example: sound_19 = 1 to sound_19 = 0 By doing so, you will permanently disable the sound it plays when a friend joins a game. Note: Remember that you can find all sounds IDs by typing !sid in any channel In the list it appears to you when you type !sid, some of the sounds come with an *(asterisk) in front, these sounds are played automatically when an event happens, for the others, you should whisper the person with /w nick send-sound For example: If you want to slap MiZiGe, do as follows: /w MiZiGe send-slap More commands /hide (Hide console. You can restore with !console from chat. /sounds (enable/disable sounds) /f (send message to all your friends) /l (lock/unlock username for /re comand) /re (reply message. No need username) /v (version) /mu (mute user) /md (delete muted users) /ml (print list of muted users) /start (start warcraft 3) !sc (Automatically spoof checks to host) Leagues that use Gproxy CZSK Romania Turkey Brasil Safelist Balkan TurkDota Egypt For a list of which commands you can use with GProxy, type !commands Or you can look the commands up here: Gproxy:Commands You can look up all the sounds here: Gproxy:SoundId's

Hosting Under Firewall Windows XP

First you must have Warcaft with PVPGN patch installed. Then: 1. Go to > My Computer -> Control Panel 2. On Control Panel open Windows Firewall Block All Incoming Connections should NOT be ticked, or else you can't host. 3. You must have Windows Firewall set to ON. 4. Then press Add Port and select: a) Port Name - at your own preference b) Port Number: 6112 c) Port Type: TCP The next step is doing the same thing, again, but at choice c), select UDP instead of TCP ( you must have both ports forwarded ) You also have to add euroloadder.exe and war3.exe to the program exception list. Click on Add Program , Find euroloader.exe in your warcraft folder and add it to the exception list. Click on Add Program , Find war3.exe in your warcraft folder and add it to the exception list. Now, you're ready to host games on Eurobattle.net! Good luck!

Hosting under Firewall on Windows 7 Tutorial

Here are a few steps so you can host under Firewall on Windows 7 1.Navigate to Computer > Control Panel 2.After you are in Control Panel navigate to Windows Firewall 3.When you enter firewall you should go to Advanced Settings 4.Than you should go to Inbound rules 5.After that add new rule 6.Now select Port and click Next 7.Now select TCP also select specific local ports and type 6112,click Next 8.Select "Allow the connection" and Click Next 9.Select all 10.Repeat the same steps and select udp instead of tcp Now you should add euroloader.exe and war3.exe in exceptions, follow steps once again and select program and instead of port you should specify the location of your euroloader.exe reapet the same for war3.exe

Portforwarding Router Tutorial

=What is port forwarding and why do you need it?= Port forwarding (sometimes referred to as tunneling or virtual servers) is the act of forwarding a network port from one network node to another. Port forwarding allows remote computers (e.g. public machines on the Internet) to connect to a specific computer within a private LAN. So in order to host a game online, you must allow public computers on the internet to connect to your computer. If you don't port forward, all incoming connections to your PC will be refused and thus no one will be able to join your game. It is required to have forwarded ports in the following types of games: Melee (standard, PG) games require at least one of the players to have his ports forwarded in order to use his computer as host for the game. If neither of the players can be the host, the game will be cancelled and everyone will be disconnected. Manually hosted games (with Create Game), only on your computer, since it will be used as the host for the game. Games created with the Ghost/Ghost++/etc bots, only on the computer where the bot is running. Solution 1 (recommended) Ports which have to be forwarded: TCP 6112-6119 UDP 6112-6119 1) Go to https://portforward.com/router.htm 2) Select your router brand from the list 3) Skip advertisement by clicking "Close" 4) Select the model of your router 5) Follow simple steps for your router model to forward the needed ports 6) You should now be able to use your pc as host for warcraft 3 games Solution 2 Paradyne router D-Link router Speedtouch router (In case solution 1 did not work, this solution contains common steps that can be used by everyone) Hello and welcome to our port forwarding guide. 1) Requirements Open cmd.exe (Start > All programs > Accessories > Command Prompt) Type ipconfig, notice the Default Gateway. NOTE: Enter Warcraft > Options > Game Play Check your Game Port, it should be 6112 on Normal Gateway and 6113 on GProxy Gateway. 2) Configuration Open your web browser, type the IP you just saw, for example, in my case I have to type http://192.168.1.254 You should see a box prompting you for your username and password. Enter your password now. By default your username and password are admin. You can find your router's username and password in your router's manual. Click the Log in button to log in to your router. Ok, Now you must search for "Port Forward", "Virtual Server" or "Game & Application Sharing". They are usually located in the advanced settings of your router. Make sure to forward both 6112 and 6113 (it is recommended to forward 6114-6119 as well). Some routers have Warcraft 3 in their database, so all you have to do is add the Warcraft 3 to the Applied Rules. If you don't have it, create a new application with the following settings: Protocol: Any Port Range: 6112-6113 Translate To: 6112-6113 Or if you don't have "Any" as a protocol type. Protocol: TCP Port: 6112-6113 Translate To: 6112-6113 Protocol: UDP Port: 6112-6113 Translate To: 6112-6113 For port forwarding and port opening it is NOT required to have a range from 6114 to 6119 opened. However, it may be useful if you are planning to host multiply games at once on your PC. 3) Get information about your router Visit http://www.portforward.com/routers.htm Search for your router's brand and exact model. Follow the instructions that are specifically made for your router in order to port forward.

Static Internal IP Router Tutorial

A -VERY- important part of setting up a Static IP address on your computer is CHOOSING an appropriate number to assign to the computer as its permanent, “static” IP address. There’s more to it than just picking any old number at random, and the number your computer has been using up until now may NOT be an appropriate choice. This is because some routers may have trouble forwarding ports to IP addresses which conflict with their DHCP server address range. That is, if the IP address on the computer is the same as one which the DHCP server might assign, the Port Forwarding may FAIL. So the FIRST step in setting up a Static IP address is to find out what range the DHCP server is set up for, and choosing a number that will NOT conflict with that range. Log into your router and look for a page that tells what the DHCP Server configuration is. This is usually found under “Advanced Configuration” and then “LAN” (or similar wording). Once you’ve found the DHCP Server page there should be one of two different ways of displaying the RANGE of addresses in the server. The first is the simplest. It gives the “Starting Address” and the “Ending Address” (or “Low” and “High”) Thus for example if you see: Starting Address 192.168.0.100 Ending Address 192.168.0.150 The “Range” of the DHCP server is FROM 192.168.0.100 TO 192.168.0.150 The second way the DHCP Server range can be displayed is to give the “Starting Address” and the “Number of Clients” (or “Number of Addresses”) Thus for example if you see: Starting Address : 192.168.0.10 Number of Clients: 50 The “Range” of the DHCP server is FROM 192.168.0.10 TO 192.168.0.60 (50 addresses, starting at 10) You must choose a number from 2 through 254 which does NOT fall within the DHCP server range, and which does NOT duplicate the address already being used by the router (the IP address you type to log into the router).. So in the first example you would be safe choosing a Static IP Address for your computer of 192.168.0.151 And in the second example you could safely choose 192.168.0.61, because these numbers are OUTSIDE of the DHCP Server range. NOTE- This is important! The "Range" of the DHCP server is INCLUSIVE. That means when we say (just for example, your router will probably be different) : Start address 192.168.0.100 End address 192.168.0.150 It means you CAN'T USE .100 OR .150 OR ANY of the numbers between them. In most cases, all you’ll need to do is check the “range” of the DHCP server and pick a safe IP address outside that range for your computer. BUT- there IS one situation which will require you to make a change to the ROUTER setup BEFORE you can go on. If you discover the DHCP server is set to use ALL possible IP addresses, then that leaves NO safe addresses for YOU to use. Starting Address 192.168.0.2 Ending Address 192.168.0.254 <-- This leaves NO addresses free for YOU to use. If the DHCP server is set to use the entire range, from .2 through .254 then you will have to CHANGE the higher figure to something lower in order to free up some addresses that will be safe for YOU to use. On the DHCP server page, CHANGE the “Ending Address” from .254 to something like .200 Starting Address 192.168.0.2 Ending Address 192.168.0.200 <-- This leaves 54 addresses free for YOU to choose. That will make the “range” of the DHCP server from .2 through 200 then you can choose any address higher than .200, in this example, 192.168.0.205 Click the “Apply” or “OK” button, then if necessary, REBOOT the router to make the change take effect. NOTE: VERY IMPORTANT!! We are picking the LAST set of digits in the IP address ONLY..! The FIRST THREE sets of digits MUST be the SAME as the ones the router and the DHCP server uses. Thus, if YOUR router uses 192.168.2.1, then you MUST pick a Static IP address that begins with 192.168.2 If YOUR router uses 10.0.0.1, then you MUST pick a Static IP address that begins with 10.0.0 Again- we’re ONLY changing the LAST set of digits. Now that you’ve decided on a compatible Static IP address to use for your computer, follow this link for a guide to setting up the IP address on your computer- However- SKIP the first few steps that tell you to look in IPCONFIG for the IP address, and just use the compatible IP address you've chosen with this guide. Skip ahead to the step (#5 in the Windows XP guide) that tells you to open the Control Panel and follow the instructions from there. http://portforward.com/networking/staticip.htm Once you've finished this procedure, the address you decided on, and configured in Windows TCP/IP Network Properties will be your "Static IP Address". Whenever anything asks for your computer's Static IP Address, this number is what it's asking for. NOTE- If your Internet connection stops working when you change Windows to a Static IP address, the reason usually is that you need to find out what your "DNS Server" addresses are. If you have this problem, read THIS guide for help on that: http://forum.portforward.com/YaBB.cgi?board=Knowledge;action=display;num=1116580819

Static Internal IP Windows Tutorial

This will guide you to how to set up a static internal IP! Before you start you need to grab some useful information for later use: Step 1. Press Start , click Run. A small window will pop up. Type cmd on it and press enter. A black window will show, then type ipconfig /all and type enter. You may get various data. You must define which one is your real internet connection. On the image below you will see an example: Take note about the IP Address , Default Gateway and Subnet Mask values, you will need them later. Now, the beggining: Step 2. Double click your connection on the system tray then click on Properties. Step 3. Select TCP/IP Protocol and then Properties. Step 4. Now, mark Use the following IP address and Use the following DNS server addresses. Recover the values you got on the Step 5 , fill the fields with the information. For DNS, type in the Default Gateway Observation: in case the Default Gateway does not work as your DNS server (unresponsive internet), you will need to enter your router interface (by typing the Default Gateway into your browser; user and pass admin or blank) and find your DNS information under DHCP settings. Now you're done setting up a static internal IP! You can now forward your ports to it and be free of problems.

Unable to join LAN game

Unable to join LAN game So your friend or brother is hosting a game and you can’t join; what to do now? There is a really cool feature in Ghost++, introduced in version 9.x which allows people on same network to play together without any problem. This feature is called the “Admin Game” and was initially designed to do a completely different job. Fortunately for us, Admin Game also solves the joining LAN games problem. First, download and set up Ghost++ or GhostOne, you can find a simple guide to do that ( TO BE ADDED) After your ghost can enter eurobattle.net and host games normally , we will make a simple modification to the configuration to allow Admin games (and thus people on same LAN to enter). Edit the ghost.cfg to include this: ADMIN GAME CONFIGURATION # whether to create the admin game or not (see readme.txt for more information) admingame_create = 1 the port GHost++ will host the admin game on (this must be different from your bot_hostport) admingame_port = 6114 the admin game password admingame_password = xpam Note: You need to set admingame_port in ghost.cfg to the port you want to host the admin game on. It *must* be different from your bnet_hostport *and* from your Warcraft 3 port. bot_hostport = 6000 admingame_port = 6114 Enter Warcraft, Options > Game Play > Port should be different (default is 6112) Save the file and start ghost.exe GHost++ automatically hosts a Warcraft 3 game (the "Admin Game") and broadcasts it to the local network. 1.) Open Warcraft 3 and go to the LAN screen. After a few seconds you will see a game called "GHost++ Admin Game" appear. Join it. 2.) Use the password command to enter your Admin Game password (e.g. !password xpam). a.) If you enter the wrong password you will be kicked from the game and temporarily banned for 5 seconds. 3.) Use the map or load command to load a map. (e.g. !map dota6.73b) 4.) Use the priv/privby/pub/pubby commands to create a game. You should wait until it says "Battle.net game hosting succeeded" before continuing. (e.g. !pub AP/Eu/PROS) 5.) Leave the game and return to the LAN screen. After a few seconds you will see your newly created game appear. Join it. 6.) You are now ready to play. Your game has been created on battle.net. 7.) If you make a mistake and want to unhost the game you can use !unhost in either game (the Admin Game or your newly created game). We are aware that this feature is easily abusable, you can choose any nickname in place of yours. This is a warning, if you abuse this feature your IP will be PERMANENTLY Banned From Eurobattle.net. No Excuses. This guide and feature is to help you. DO NOT ABUSE IT. Unable to join own or LAN game (ADSL users) Hi guys, after few weeks of trying to solve problem of joining your own game, or game created by other machine in Local Area Network (LAN), I finally managed to get it to work. PLEASE NOTE: This solution maybe not work for you! These settings are usually for ADSL users! The solution for this problem is in general: 1.Turn your router/gateway in Pure Bridge mode 2. Enable PPPoE connection on all of your computers (You will need the username and password from your ISP) 3.Fix your firewall rules 4.Try to host public game, if everyone (from the internet) can join, then try to join your other machines on LAN This works for most of routers that doesn`t support NAT Loopback, but the settings about pure bridge mode, may be different, based on your router and it`s own firmware.